Scaffold Spring Clips are used to secure a Coupling Pin in a frame leg. When stacking scaffold, we recommend using a Spring Clip for pinning the Coupling Pin to the bottom frame leg and a Toggle Pin, Pig Tail Pin or Span Pin for fastening the Coupling Pin to the top frame leg.

Scaffold Pig Tail Pins are commonly used to secure the upper hole of a Coupling Pin to a Scaffold Frame Leg. Also used to pin Casters, Side Brackets, Guard Rail Posts, etc.

Scaffold Toggle Pins are commonly used to secure the upper hole of a Coupling Pin to a Scaffold Frame Leg. Also used to pin Casters, Side Brackets, Guard Rail Posts, etc.

Scaffold Span Pins are commonly used to secure a Caster in a Socket Jack or Scaffold Frame. Span Pins are also used to pin Guard Rail Posts, top frame leg to the Coupling Pin, etc.

Scaffolds Supply's 9" Coupling Pin (1-7/16" Ø) with 1" Collar is to be used with a 1.69" Ø frame leg (1-11/16"). The collar helps to evenly distribute the weight of the top frame while the tapered ends allow for easy stacking.
Does not include the Spring Clip.

While other suppliers offer zinc-plated Guard Rails that end up full of rust within a year, Scaffolds Supply Cross Braces are Hot-Dipped Galvanized BEFORE the ends are pressed to ensure the entire surface of the Guard Rail is protected for maximum longevity!

• This Guard Rail satisfies OSHA fall protection requirements when installed correctly
• Ends of Guard Rails are stamped with dimensions
• This Guard Rail is 3'L center of hole to center of hole
• Pre-Hot Dipped Galvanized for maximum longevity

Scaffolds Supply's Base Plate can be used in conjunction with our Socket Jack or inserted directly into a Scaffold Frame leg.

• Fits 1.625" & 1.69" Scaffold Frames
• Base Plates provide a solid foundation for your frames and help to distribute weight evenly
• Electroplated for longevity & rust prevention

While other suppliers offer zinc-plated Guard Rails that end up full of rust within a year, Scaffolds Supply Cross Braces are Hot-Dipped Galvanized BEFORE the ends are pressed to ensure the entire surface of the Guard Rail is protected for maximum longevity!

• This Guard Rail satisfies OSHA fall protection requirements when installed correctly
• Ends of Guard Rails are stamped with dimensions
• This Guard Rail is 42"L center of hole to center of hole
• Pre-Hot Dipped Galvanized for maximum longevity

While other suppliers offer zinc-plated Guard Rails that end up full of rust within a year, Scaffolds Supply Cross Braces are Hot-Dipped Galvanized BEFORE the ends are pressed to ensure the entire surface of the Guard Rail is protected for maximum longevity!

• This Guard Rail satisfies OSHA fall protection requirements when installed correctly
• Ends of Guard Rails are stamped with dimensions
• This Guard Rail is 5'L center of hole to center of hole
• Pre-Hot Dipped Galvanized for maximum longevity

Scaffolds Supply's Swivel Base Plate can be used in conjunction with our Socket Jack or inserted directly into a Scaffold Frame leg.

• Perfect for sloped surfaces and pitched roofs!
• Swivel Base Plates provide a solid foundation for your frames and help to distribute weight evenly
• Electroplated for longevity & rust prevention

While other suppliers offer zinc-plated Guard Rails that end up full of rust within a year, Scaffolds Supply Cross Braces are Hot-Dipped Galvanized BEFORE the ends are pressed to ensure the entire surface of the Guard Rail is protected for maximum longevity!

• This Guard Rail satisfies OSHA fall protection requirements when installed correctly
• Ends of Guard Rails are stamped with dimensions
• This Guard Rail is 7'L center of hole to center of hole
• Pre-Hot Dipped Galvanized for maximum longevity

Wall Ties are used to secure the scaffold to a solid structure. Scaffolds Supply's Universal Wall Tie is secured to the Scaffold Vertical with our 2" x 2" Right Angle Clamp. Then secured to the solid structure with either a 5/8" Sleeve Anchor Bolt or No.9 Tie Wire.

This 12" Side Bracket has a "Pig Ear" hook design that allows it to be used on both the 1.69" outer frame as well as 1" frame rungs. Our blue powder coating will minimize scratching as well as prevent rusting to maximize longevity!

-Don't forget the Toggle Pin to secure the bottom saddle to the frame leg!
-Should not be used with free standing Scaffold Towers!

While other suppliers offer zinc-plated Guard Rails that end up full of rust within a year, Scaffolds Supply Cross Braces are Hot-Dipped Galvanized BEFORE the ends are pressed to ensure the entire surface of the Guard Rail is protected for maximum longevity!

• This Guard Rail satisfies OSHA fall protection requirements when installed correctly
• Ends of Guard Rails are stamped with dimensions
• This Guard Rail is 10'L center of hole to center of hole
• Pre-Hot Dipped Galvanized for maximum longevity

A Starter Bar is used in the ground level section of a scaffold tower to begin a run of stairs. Scaffolds Supply's Starter Bar is blue powder coated to resist rust and scratching for maximum longevity!

• Screw Jacks, Socket Jacks or Swivel Jacks are required to use a Starter Bar!
• Used to begin the base section of a Stair Tower
• For use with 5'W Scaffold Frames
• Powder coated finish to prevent rusting & scratching

Scaffolds Supply's Female Guard Rail Post with Drop Locks meets OSHA's guard rail and fall protection requirements when installed properly. Don't forget the Toggle Pin, Span Pin or Pig Tail Pin to properly secure the bottom of your post onto your Coupling Pin.

• This Guard Rail Post fits over a 1-7/16" Coupling Pin and is then locked in place with a Toggle Pin, Span Pin or Pig Tail Pin
• Compatible with 1.69" S-Style Scaffold Frames
• Upper and lower locks secure Guard Rails at approximately knee and waist level (21" & 42" per OSHA requirements) to prevent workers from stepping or backing off the working platform level of a scaffolding while in use.
• Blue powder coating to prevent & protect against rust & scratching

Scaffolds Supply's Cross Braces are Hot-Dipped Galvanized before the ends are pressed for maximum protection from rusting!

• 5' x 3' x 4' Tubular Cross Brace
• Double punched to fit Scaffold Frames with 3' & 4' Lock Spans to create 5' bays
• Cross Brace dimensions are stamped on the ends
• Hot-Dipped Galvanized to prevent rusting

Scaffolds Supply's Bolt-On Style Ladder Bracket attaches to the Scaffold Frame with a 2" Dual Purpose Half Clamp. Our Ladder Bracket is constructed of High-Strength Steel and blue powder coated for maximum longevity!

• This Bolt-On Style Ladder Bracket utilizes a 2" Dual Purpose Half Clamp to attach to the Scaffold Frame
• This Ladder Bracket is 15" wide
• Use 2pc Ladder Brackets to secure your first ladder & 1pc Ladder Bracket for each section above it (you will always have 1pc more ladder brackets than ladders per each ladder run)
• We powder coated our High-Strength Steel Ladder Brackets to resist rust & minimize scratching

Scaffolds Supply's Cross Braces are Hot-Dipped Galvanized before the ends are pressed for maximum protection from rusting!

• 7' x 3' x 4' Tubular Cross Brace
• Double punched to fit Scaffold Frames with 3' & 4' Lock Spans to create 7' bays
• Cross Brace dimensions are stamped on the ends
• Hot-Dipped Galvanized to prevent rusting

Scaffolds Supply's Female Guard Rail Post with Candy Cane Locks meets OSHA's guard rail and fall protection requirements when installed properly. Don't forget the Toggle Pin, Span Pin or Pig Tail Pin to properly secure the bottom of your post onto your Coupling Pin.

• This Guard Rail Post fits over a 1-7/16" Coupling Pin and is then locked in place with a Toggle Pin, Span Pin or Pig Tail Pin
• Compatible with 1.69" S-Style Scaffold Frames
• Upper and lower locks secure Guard Rails at approximately knee and waist level (21" & 42" per OSHA requirements) to prevent workers from stepping or backing off the working platform level of a scaffolding while in use.
• Blue powder coating to prevent & protect against rust & scratching

Scaffolds Supply's Frame Screw Jacks have a solid 24" threaded stem welded to a fixed Base Plate. Screw Jacks allow for individual leveling of each leg to ensure a level working platform on uneven terrane.

• 24" overall stem length, 18" adjustable stem length
• Notched 6" from the top to prevent over-extending & the nut from coming off
• Acme Threads
• 5" x 5" Welded on Base Plate
• Electroplated for longevity & rust prevention

Scaffolds Supply's Socket Jacks can be used in conjunction with a Caster, Fixed Base Plate or Swivel Base Plate for added adjustability. Socket Jacks allow for individual leveling of each leg to ensure even your Rolling Scaffold Towers have a level working platform on uneven surfaces.

• 28" overall stem length, 16" adjustable stem length
• Notched 6" from the top to prevent over-extending & the nut from coming off
• Acme Threads
• Socket accepts a 1-3/8" stem of our 8" Caster, Base Plate & Swivel Base Plate
• Electroplated for longevity & rust prevention

Scaffolds Supply's 3' Access Ladder is stackable with male and female ends that slip into one another. All of our Access Ladders are constructed of High-Strength Steel and blue powder coated for maximum longevity!

• This Access Ladder is stackable & compatible with our 6' Access Ladders
• Always build with male ends up
• This ladder is 15" wide with rungs evenly spaced 11" apart
• Secure the Access Ladder to the Scaffold Frame using our Bolt On Ladder Bracket
• Use 2pc Ladder Brackets to secure your first ladder & 1pc Ladder Bracket for each section above it (you will always have 1pc more ladder brackets than ladders per each ladder run)

This 21" Side Bracket has a "Pig Ear" hook design that allows it to be used on both the 1.69" outer frame as well as 1" frame rungs. Our blue powder coating will minimize scratching as well as prevent rusting to maximize longevity!

-Don't forget the Toggle Pin to secure the bottom saddle to the frame leg!
-Bracket will hold 2pc Wood Plank, 2pc Steel Hook on Plank or 1pc Aluminum Hook on Deck
-Should not be used with free standing Scaffold Towers!

Scaffolds Supply's 23" Angle Iron Side Bracket has a Saddle Style hook. This durable 2-Board Bracket is made of High Strength Angle Iron Steel and powder coated red to minimize scratching as well as prevent rusting for maximum longevity.

-Don't forget the Toggle Pin to secure the bottom saddle to the frame leg!
-Bracket will hold 2pc Wood Plank, 2pc Steel Hook on Plank or 1pc Aluminum Hook on Deck
-Should not be used with free standing Scaffold Towers!

Similar to our SB-215, Scaffolds Supply's 21" Saddle Side Bracket has a Saddle Style hook which provides additional strength and stability with less movement than most standard hanging bracket. The diagonal tubing is also beefed up from a 1" Ø to a 1.26" Ø. Our blue powder coating will minimize scratching as well as prevent rusting to maximize longevity.

-Don't forget the Toggle Pins (2pc per bracket) to secure the top saddle hook & the bottom saddle to the frame leg!
-Bracket will hold 2pc Wood Plank, 2pc Steel Hook on Plank or 1pc Aluminum Hook on Deck
-Should not be used with free standing Scaffold Towers!

Scaffolds Supply's 2-Board End Bracket attaches to the end of a frame to form a platform perpendicular (90°) to a platform created by the frame and a side bracket. End Brackets are commonly used to turn a corner with the scaffolding. Our blue powder coating will minimize scratching as well as prevent rusting to maximize longevity!

-Don't forget the Toggle Pins to secure the top saddle hook & the bottom saddle to the frame leg!
-Bracket will hold 2pc Wood Plank, 2pc Steel Hook on Plank or 1pc Aluminum Hook on Deck
-Should not be used with free standing Scaffold Towers!

Scaffolds Supply's 30" Saddle Side Bracket has a Saddle Style hook which provides additional strength and stability with less movement than most standard hanging bracket. The diagonal tubing is also beefed up from a 1" Ø to a 1.26" Ø. Our blue powder coating will minimize scratching as well as prevent rusting to maximize longevity.

-Don't forget the Toggle Pins (2pc per bracket) to secure the top saddle hook & the bottom saddle to the frame leg!
-Bracket will hold 3pc Wood Plank, 3pc Steel Hook on Plank or 1pc Aluminum Hook on Deck
-Should not be used with free standing Scaffold Towers!

Scaffolds Supply's Swivel Jacks are perfect for use on inclined surfaces or pitched roofs!
Swivel Jacks allow for individual leveling of each leg to ensure a level working platform on uneven terrane.

• 24" overall stem length, 18" adjustable stem length
• Notched 6" from the top to prevent over-extending & the nut from coming off
• Acme Threads
• 6" x 6" Welded on Base Plate
• Electroplated for longevity & rust prevention

Scaffolds Supply's Cross Braces are Hot-Dipped Galvanized before the ends are pressed for maximum protection from rusting!

• 10' x 3' x 4' Tubular Cross Brace
• Double punched to fit Scaffold Frames with 3' & 4' Lock Spans to create 10' bays
• Cross Brace dimensions are stamped on the ends
• Hot-Dipped Galvanized to prevent rusting